Breathe New Life into Your Engine (MAF sensor replacement)

If you’ve noticed your vehicle is hard to start, stalling, or has lost power, the culprit may be a part with an odd name: the MAF sensor.  You may have never even heard of a MAF sensor, but it’s important that it be working correctly, or you may be experiencing some fairly significant engine issues.

All vehicles bring in air and direct it through an air filter before it goes into your engine, where it mixes with fuel to provide power to get you going. There’s a tube-like device with a sensor inside it that measures how much of that mass of air is passing through. That’s why it’s called a mass air flow sensor, or MAF sensor.  If the MAF sensor isn’t working right, the engine’s computer can’t figure out the right amount of fuel to mix with it, and your engine may hesitate or stall.  Sometimes this will cause your Check Engine Light to come on, and any time it does that, make sure you have your vehicle checked by a professional, so you’ll know what’s going on.

When you take your vehicle into your service facility, a technician will thoroughly check the system to see just where the problems are.  If your air filter is dirty, your MAF sensor may get dirty too, which might be causing the problems.  You may find your fuel economy isn’t what it used to be either.

There are other things that can cause the same symptoms, too, such as a leak in a vacuum hose. It’s also possible that the electrical connector between the MAF sensor and the engine has broken. 

The technician can use electronic diagnostic equipment to help pinpoint the exact problem or problems, replace worn parts, and test drive your vehicle to make sure it’s working correctly.

It’s also a good idea to make sure your air filter is changed regularly. A dirty air filter can contribute to a MAF sensor failure. One of the big benefits of having your vehicle regularly maintained at one facility, is they know your vehicle. So, they keep track of which of your vehicle’s parts should be periodically replaced before problems develop. 

If you keep clean air heading into your engine, it can help your engine work efficiently, and with the power it was engineered to deliver. Isn’t that a breath of fresh air?

Corporate Autoworks
5195 Harvester Rd. Unit#1
Burlington, ON L7L 6E9
905-333-9201
http://www.corporate-autoworks.com

Don't Be Shocked (Shock Absorbers)

If you've ever ridden down a rough road on your bicycle, you know how hard a ride it can be.  Yet drive down the same road in your car, truck or SUV and it miraculously will smooth out the ride.  That's because it is equipped with shock absorbers.  They are built to dampen impacts from road irregularities.  But after taking hundreds of hits from potholes, railroad tracks and curbs, your shock absorbers can wear out.  Besides the rough ride that can cause, there are other ways your vehicle's performance can be affected.

When it comes to braking for example, you may take a longer distance to stop.  That's because shocks help keep your tires in contact with the surface of the road.  If the shocks aren't working properly, the tires won't make contact like they should.  So when you slam on the brakes, your vehicle will take longer to stop.

Consider what worn out shocks are doing to your tires.  Since the bumps aren't being dampened as much, your tires can bounce up and down more.  That can produce a problem of uneven wear called cupping.

And when you start out from a stop, your vehicle may not have the traction it should since the shocks aren't keeping them down on the road as you accelerate.  If you have front wheel drive, you may lose some steering control on acceleration. Obviously, many of these things involve safety concerns.

Pay attention to any deterioration in your vehicle's ride quality.  If your vehicle is starting to bounce up and down and its ride feels bumpier than before, head on over to your vehicle service facility and get your suspension checked out.  Do the same if steering response isn't as good as it used to be.  Notice that your vehicle nose dives when you brake?  Are your tires wearing in an unusual manner? All are signs that your shocks may be on their last legs.

If the last time you replaced your shocks was 50,000 miles/80,000 kilometers ago, a technician should evaluate them.  Don't be "shocked" if it's time for new ones.

Corporate Autoworks
5195 Harvester Rd. Unit#1
Burlington, ON L7L 6E9
905-333-9201
http://www.corporate-autoworks.com

How Much is Enough for Burlington Auto Owners? Tire Tread Depth

Most Burlington drivers know that tires wear out and that the wear has to do with tread depth. Most of us have heard that “bald” tires are dangerous, but most of us picture a tire with no tread at all when we think of a bald tire. And when we take our vehicles in for preventive maintenance, the technician tells us they're need to be replaced long before all the tread is worn off. Just how much tire tread wear is too much? And how can you tell? Tires are and their condition is important to the safe handling of a vehicle, so it's for Burlington vehicle owners to know the answers to these questions.

First of all, it's important to understand that there may be a legal limit to tread wear. If your tires are worn past this limit, you have to replace them to be in compliance with ON auto safety laws. That's why measuring your tread wear is part of a vehicle safety inspection.

In some jurisdictions, tread must be at least 1.6 millimeters or 2/32 of an inch thick. This standard has been in effect since 1968. But this standard has recently been called into question, and some ON professionals are arguing that it be changed.

The safety issue that has brought this standard under scrutiny is the ability of a vehicle to stop on a wet surface. When a vehicle has trouble stopping, most Burlington drivers immediately look at the brakes as the source of the problem. But tires are crucial to safe stopping distances because they provide the traction required in a stop.

A tire's contact with the road surface creates traction, which allows for effective braking. On a wet surface, a tire only has traction if it can get to the road's surface. So tire tread is designed to channel water out from under the tire to allow it to stay in contact with the road. If the tire can't shift the water, then it starts to “float.” This condition is called hydroplaning. It is very dangerous for Burlington drivers since the vehicle won't stop no matter how hard the driver presses the brakes. Steering control is also lost.

A recent study tested the stopping ability of a passenger car and a full-sized pick-up on a road surface covered with only a dime's depth of water (less than a millimeter). The vehicles were traveling at 70 mph (112 kph) when they stopped on the wet surface. At 2/32 (1.6 mm) tread depth, the stopping distance was double that of a new tire. The passenger car was still traveling at 55 mph (89 kph) when it reached the stopping distance it experienced with new tires.

Let's suppose that you're on a busy Burlington road in a light drizzle and a vehicle stops suddenly in front of you. You just bought new tires and you brake hard, missing the vehicle with only inches to spare. If you hadn't bought those new tires, you would have crashed into that vehicle at 55 mph (89 kph). That is a major difference.

What if your tires had a tread depth of 4/32 (3.2 mm)? You would have crashed into that vehicle at 45 mph (72 kph). Still not a good situation. But it's better.

Now what if you were driving that pick-up truck? You wouldn't have missed that vehicle in the first place, and you would have crashed at higher rates of speed in both of the other scenarios. The heavier your vehicle, the longer its stopping distance. It's a matter of physics.

The results of this test has led Consumer Reports and others to ask that the standard for tread wear be changed from 2/32 (1.6 mm) to 4/32 (3.2 mm). The increased standard will improve safety on the road and save lives here in ON and nationally.

Of course, until the standard changes, you'll have to decide whether you'll be willing to replace your tires a little sooner.

You can use an American quarter to tell if your tread wear is down to 4/32 (3.2 mm). Place the quarter into the tread with George's head toward the tire and his neck toward you. If the tread doesn't cover George's hairline, you're under 4/32 (3.2 mm). With a Canadian quarter, the tread should cover the digits of the year.

You can measure the 2/32 inch (1.6 mm) tread wear with a penny. If the tread touches the top of Abe's head, it's at 2/32 (1.6 mm). Tires are super important when it comes to vehicle care. But their condition has a major impact on safety. We need to decide whether to sacrifice safety for economy. Keeping our tread wear above 4/32 in (3.2 mm) is good auto advice.

Corporate Autoworks
5195 Harvester Rd. Unit#1
Burlington, ON L7L 6E9
905-333-9201
corporateautoworks.autotipsblog.com

'Tis the Season (Tires)

We all know about winter tires.  But did you know there is such a thing as summer tires?

Most people have all-season tires on their vehicles.  They work pretty well in a variety of weather conditions.  But if you want better handling and performance, you might consider switching to summer tires.  Here are a few things you should know about them.

Summer tires are good for high-performance vehicles like sports cars and luxury SUVs, but they don't have to be limited to those. They have a different tread pattern than all-season tires, with generally shallower grooves and more rubber that contacts the road.  The rubber is made of a stickier compound good for taking corners at higher speeds.  Plus it is engineered so it stays firmer the hotter the temperature gets. 

Here's a bonus.  That design also works well in warm, wet weather.  It makes sense, since more the more rubber that's touching the concrete or asphalt when it's slippery out, the better the traction. 

There are some things to be aware of with summer tires.  They often have asymmetrical or unidirectional tread patterns.  That sometimes limits the way these tires can be rotated on a vehicle.  Another thing to remember is it is NOT a good idea to use summer tires in any wintery conditions.  They lose traction as the temperature heads toward the freezing range and below since that rubber that's designed to stay firm at warm temperatures gets hard as a rock when they freeze.

But in warmer weather, summer tires can increase your braking and cornering capabilities.  Plus you'll notice more grip at faster speeds and higher temperatures than all-season tires.  So think about discussing summer tires with your service advisor to see if they'd be a good fit for the type of driving you do.  He or she will offer you some choices that are designed to meet your vehicle's specs.

Corporate Autoworks
5195 Harvester Rd. Unit#1
Burlington, ON L7L 6E9
905-333-9201
http://www.corporate-autoworks.com

In a Fog (Fogged Windows in Cold Weather)

It's bad enough in cold weather when ice and snow block your visibility.  Add to that fog on the inside of your windows and you could be driving blind.  So here are a few tips on how to keep your windows from fogging up when there's a chill in the air.

You probably know fog is really condensation, when moist, warm air meets a cold surface and turns to liquid.  If your windshield fogs up, you probably turn on your windshield defroster. Most defrosters blow heated air on the windshield glass to warm it up so it won't condense the moisture.  Many also turn on the air conditioning to reduce the moisture. 

That same strategy can work on the rest of the windows.  First, turn up your heater's temperature setting.  The hotter the air, the more moisture it will hold.  Also, turn off the "recirculating" setting since you want all outside air to come in. Then switch on the air conditioning.  It will remove the moisture from the outside  air that it's blowing inside the cabin.  Try cracking a couple of windows to make it easier for the air to flow. This should do the trick pretty quickly. 

There's one other thing to try.  Many vehicles have electric heater elements embedded in the rear window glass (the rear window defroster) and in the outside rearview mirror glass. Make sure to turn those on, too; sometimes they're on the same switch.

For all of these things to work, of course, your vehicle's components have to be maintained so they'll do the things they're designed to do.  And you didn't think it was important to have your air conditioning working in the cold weather months! 

One final tip.  Keep the insides of your windows CLEAN.  Oil and dirt on the glass give the water molecules something to latch on to.  That ought to clear up this problem.

Corporate Autoworks
5195 Harvester Rd. Unit#1
Burlington, ON L7L 6E9
905-333-9201
http://www.corporate-autoworks.com